Blar i SINTEF Industri på tittel
Viser treff 872-891 av 1534
-
Materials testing and characterization of four X60-X65 pipeline steels
(Research report, 2021)This report summarizes the main results from the slow strain rate tensile testing campaign performed within the framework of the HyLINE project. The base metals and weld simulated heat affected zones of four pipeline steels, ... -
Mathematical Modeling of Furnace Drainage While Tapping Slag and Metal Through a Single Tap-Hole
(Peer reviewed; Journal article, 2020)Furnace tapping is a critical operation on pyrometallurgical furnaces known for unpredictable performance in many cases. A reduced order mathematical model capable of predicting tapping rates of both slag and metal is ... -
Measurement of anode anisotropy by micro x-ray computed tomography
(The Minerals, Metals & Materials Series;2367-1181, Peer reviewed; Journal article, 2019)Micro X-ray Computed Tomography (CT) is an instrumental method for recording inner structure 3D images without damaging the observed volume. A methodology has been developed by SINTEF for CT of carbonaceous materials, ... -
Measuring In Situ Interfacial Contact Resistance in a Proton Exchange Membrane Fuel Cell
(Peer reviewed; Journal article, 2019)Interfacial contact resistance (ICR) is one of the remaining hurdles for successful implementation of stainless steel bipolar plates in PEM fuel cells. We have developed a reliable method, using thin gold wires, to measure ... -
Measuring particle concentration of multimodal synthetic reference materials and extracellular vesicles with orthogonal techniques: Who is up to the challenge?
(Peer reviewed; Journal article, 2021)The measurement of physicochemical properties of polydisperse complex biological samples, for example, extracellular vesicles, is critical to assess their quality, for example, resulting from their production and isolation ... -
Measuring particle size distribution and mass concentration of nanoplastics and microplastics: addressing some analytical challenges in the sub-micron size range
(Peer reviewed; Journal article, 2021)HYPOTHESIS:The implementation of the proposal from the European Chemical Agency (ECHA) to restrict the use of nanoplastics (NP) and microplastics (MP) in consumer products will require reliable methods to perform size and ... -
Measuring the thermal conductivity of membrane and porous transport layer in proton and anion exchange membrane water electrolyzers for temperature distribution modeling
(Peer reviewed; Journal article, 2019)Water electrolyzers that use a membrane electrolyte between the electrodes are a promising technology towards mass production of renewable hydrogen. High power setups produce a lot of heat which has to be transported through ... -
The mechanical properties of a model hydrogenated nitrile butadiene rubber (HNBR) following simulated sweet oil exposure at elevated temperature and pressure
(Peer reviewed; Journal article, 2015)A typical carbon black reinforced hydrogenated nitrile butadiene rubber (HNBR) was exposed to a mix of hydrocarbons (toluene, heptane and cyclohexane) at elevated temperatures and pressure in order to chemically age the ... -
Mechanical Properties of AlSi10Mg Processed by Laser Powder Bed Fusion at Elevated Temperature
(The Minerals, Metals & Materials Series;2367-1181, Peer reviewed; Journal article, 2020)AlSi10Mg processed by laser powder bed fusion is expected to have remarkable mechanical properties due to the dominant cellular microstructure. However, the as-processed material is often both anisotropic and containing ... -
Mechanism behind the Inhibiting Effect of CO2 on the Oxidation of Al−Mg Alloys
(Peer reviewed; Journal article, 2018)Al–Mg alloys are known to suffer from problematic oxidation during melting, refining, and casting. The use of a CO2/air cover gas is known to minimize this oxidation; however, a mechanistic understanding of the beneficial ... -
The Mechanism Behind the Oxidation Protection of High Mg Al Alloys with Beryllium
(Peer reviewed; Journal article, 2018)The addition of beryllium to Al-Mg alloys is known to cause a dramatic decrease in oxidation; however, the mechanism behind this protective effect is not yet fully understood. To aid in finding an alternative to the toxic ... -
Mechanisms and Thermochemistry of Reactions of SiO and Si2O2 with OH and H2O
(Peer reviewed; Journal article, 2023)This paper reports on computational studies of gas-phase reactions of SiO and Si2O2. The oxidation of SiO can initiate efficient formation of silica or silicate dust particles in a wide range of environments. Both OH ... -
Mechanisms of SiO oxidation: Implications for dust formation
(Peer reviewed; Journal article, 2023)Reactions of SiO molecules have been postulated to initiate efficient formation of silicate dust particles in outflows around dying (AGB) stars. Both OH radicals and H2O molecules can be present in these environments and ... -
Mechanisms of Toxicity of Industrially Relevant Silicomanganese Dust on Human 1321N1 Astrocytoma Cells: An In Vitro Study
(Peer reviewed; Journal article, 2019)Tremendous efforts are applied in the ferroalloy industry to control and reduce exposure to dust generated during the production process, as inhalable Mn-containing particulate matter has been linked to neurodegenerative ... -
Mechanisms of Toxicity of Industrially Relevant Silicomanganese Dust on Human 1321N1 Astrocytoma Cells: An In Vitro Study
(Journal article; Peer reviewed, 2019)Tremendous efforts are applied in the ferroalloy industry to control and reduce exposure to dust generated during the production process, as inhalable Mn-containing particulate matter has been linked to neurodegenerative ... -
Melting cell based compensated design method for improving dimensional accuracy of additively manufactured thin channels
(Peer reviewed; Journal article, 2020)Powder-bed fusion additive manufacturing technology makes it possible to produce parts with complicated geometry and high accuracy. However, dimensional deviation caused by powder overmelting and dross formation is still ... -
Metabolite interactions in the bacterial Calvin cycle and implications for flux regulation
(Peer reviewed; Journal article, 2023)Metabolite-level regulation of enzyme activity is important for microbes to cope with environmental shifts. Knowledge of such regulations can also guide strain engineering for biotechnology. Here we apply limited ... -
Metal- and covalent-organic framework mixed matrix membranes for CO2 separation: A perspective on stability and scalability
(Peer reviewed; Journal article, 2023)Membrane technology has attracted great industrial interest in carbon capture and separation owing to the merits of energy-efficiency, environmental friendliness and low capital investment. Conventional polymeric membranes ... -
Metallic foam supported electrodes for molten carbonate fuel cells
(Peer reviewed; Journal article, 2020)This paper demonstrates the benefits of using a metallic foam support within molten carbonate fuel cell (MCFC) cathodes. A state-of-the-art fabrication process based on tape casting has been developed to produce microporous ... -
Metallurgical Aspects in the Welding of Clad Pipelines—A Global Outlook
(Journal article; Peer reviewed, 2019)In the present work, the metallurgical changes in the welding of clad pipelines are studied. Clad pipes consist of a complex multi-material system, with (i) the clad being stainless steel or a nickel-based superalloy, (ii) ...