Blar i SINTEF Industri på tittel
Viser treff 1264-1283 av 1566
-
RobustNot - Dokumentasjon av mekaniske egenskaper og dimensjoner til notlin i oppdrettsnøter
(SINTEF Rapport;2018:00971, Research report, 2018) -
Rock physics model of shale: Predictive aspect
(Peer reviewed; Journal article, 2021)Shales often show strong elastic anisotropy that originate from the alignment and platy nature of its constituent minerals. Despite its impact on AVO (Amplitude Variation with Offset) response and seismic time-shifts, ... -
Role of Adsorbate Coverage on the Oxygen Dissociation Rate on Sr-Doped LaMnO3 Surfaces in the Presence of H2O and CO2
(Peer reviewed; Journal article, 2020)Sr-doped LaMnO3 (LSM) is a promising oxygen reduction reaction electrocatalyst in solid oxide fuel cells and other electrochemical devices. The presence of CO2 and H2O has been reported to promote the oxygen dissociation ... -
The Role of Grain Boundary Precipitates during Intergranular Fracture in 6xxx Series Aluminium Alloys
(Peer reviewed; Journal article, 2021)During ageing, 6xxx aluminium alloys will develop a microstructure characterised by needle-shaped Mg/Si-rich precipitates in the bulk, precipitate-free zones along the grain boundaries and larger Mg/Si-rich precipitates ... -
Role of metal quality and porosity formation in low pressure die casting of A356: Experimental observations
(Peer reviewed; Journal article, 2021)Porosity is one of the major problems in casting operations and there are several discussions in the literature about the porosity formation in aluminum castings. Bifilms are the defects that are introduced into the melt ... -
Role of Pitting in the Formation of Potholes in Carbon Cathodes - A Review
(Journal article, 2016) -
The role of sustainability characteristics in the diffusion of renewable energy technologies
(Peer reviewed; Journal article, 2023)This paper aims to investigate the role of sustainability factors in the diffusion of solar photovoltaic (PV) technologies. A combined economic innovation-diffusion model that accounts for additional sustainability aspects ... -
Room temperature creep mechanism of a Pb-Sn-Sb lead alloy
(Peer reviewed; Journal article, 2019)Lead alloys are the most common materials adopted for the production of subsea power cable sheathing. The sheathing is a layer of stable and watertight metal, which serves to prevent the electrical failure of the cable. ... -
Root causes for corrosion on painted steel structures in marine environments
(Peer reviewed; Journal article, 2023)Our understanding of the failure mechanisms of coatings, for example, cathodic disbonding, corrosion creep, blistering, and cracking, have been developed to a high level over the past decades. However, knowing what actually ... -
Root formation and mechanical properties in laser keyhole welding of 15 mm thick HSLA steel
(Peer reviewed; Journal article, 2021)Deep penetration laser welding is promising in joining thick (> 10 mm) steel sections. Focused laser beam by drilling vapour cavity, the keyhole, generates deep and narrow welds. Full penetration single-pass joining has a ... -
Root formation and metallurgical challenges in laser beam and laser-arc hybrid welding of thick structural steel
(Peer reviewed; Journal article, 2021)Single-pass laser beam welding (LBW) of steel components with wall thickness of > 10 mm is of high interest due to enhanced productivity. Deep penetration LBW provides excessive hardness and certain quality issues such as ... -
Rotating bed reactor for CLC: Bed characteristics dependencies on internal gas mixing
(Peer reviewed; Journal article, 2014)A newly designed continuous lab-scale rotating bed reactor for chemical looping combustion using CuO/Al2O3 oxygen carrier spheres and methane as fuel gives around 90% CH4 conversion and >90% CO2 capture efficiency based ... -
Salt clogging during supercritical CO2 injection into a downscaled borehole model
(Journal article; Peer reviewed, 2019)Injection of CO2 into saline storage aquifers is often accompanied by drying of the formation water and salt precipitation. Subsequent salt clogging of a well bore and the near wellbore rock matrix may lead to injectivity ... -
Sandblasting effect on performance and durability of Ti based IrO2 –Ta2O5 anode in acidic solutions
(Peer reviewed; Journal article, 2018)The effect of applying sandblasting during pretreatment while preparing titanium based IrO2 – Ta2O5 anodes by the conventional method was investigated. It was observed that sandblasting influences the surface morphology ... -
SAPO-37 microporous catalysts: revealing the structural transformations during template removal
(Peer reviewed; Journal article, 2017)We have studied the structural behavior of SAPO-37 during calcination using simultaneous in situ powder X-ray diffraction (PXRD) and mass spectroscopy (MS) in addition to ex situ thermogravimetric analysis (TGA) and ... -
Scanning Precession Electron Diffraction to aid Aluminum Alloy Development
(Peer reviewed; Journal article, 2019) -
Scenario generation by selection from historical data
(Peer reviewed; Journal article, 2021)In this paper, we present and compare several methods for generating scenarios for stochastic-programming models by direct selection from historical data. The methods rangefromstandardsamplingandk-means,throughiteratives ... -
Screening Cellulose Spinning Parameters for Fabrication of Novel Carbon Hollow Fiber Membranes for Gas Separation
(Peer reviewed; Journal article, 2019)Novel carbon hollow fiber membranes (CHFMs) have been, for the first time, prepared from cellulose precursors directly spun with a cellulose/(1-ethyl-3-methylimidazolium acetate (EmimAc) + dimethyl sulfoxide (DMSO)) system. ... -
Screening of strong bicarbonate forming solvents for CO2 capture
(Journal article; Peer reviewed, 2017) -
Screening of thermoelectric silicides with atomistic transport calculations
(Peer reviewed; Journal article, 2020)More than 1000 crystalline silicide materials have been screened for thermoelectric properties using first-principles atomistic calculations coupled with the semi-classical Boltzmann transport equation. Compounds that ...