Blar i SINTEF Open på tittel
Viser treff 2576-2595 av 10305
-
Effect of Filling Pressure on Post-Arc Gap Recovery of N2
(Peer reviewed; Journal article, 2020)Experimental investigation of the effect of filling pressure on the post-arc dielectric recovery characteristics of nitrogen is reported in this paper. A half-cycle arc current duration of 540 μs followed by a 10 kV pulse ... -
Effect of forced convection on the hygrothermal performance of a wood frame wall with wood fibre insulation
(Peer reviewed; Journal article, 2021)Wood-based thermal insulation materials have interesting hygroscopic characteristics because of their high moisture capacity. The present paper investigates the moisture conditions in wood-frame walls with wood fibre thermal ... -
The effect of freeze-chilling on quality changes of cod loins (Gadus morhua) during chilled storage
(Chapter; Peer reviewed, 2022)Fish is highly perishable and has a short shelf-life. Freeze-chilling involves freezing and frozen storage followed by thawing and chilled storage. It offers more sustainable logistic benefits as it enables the products ... -
The effect of frictional pressure, geometry and wall friction on the modelling of a pseudo-2D bubbling fluidised bed reactor
(Peer reviewed; Journal article, 2015)The two fluid model (TFM) closed by the kinetic theory of granular flows (KTGF) has been developed to a high level of maturity over the past three decades. However, significant uncertainties still remain about the influence ... -
Effect of fuel mixing on melting behavior of spruce wood ash
(Journal article, 2019)The aim of this work was to investigate effects of fuel mixing on melting behavior of spruce wood ash. Spruce bark was studied as additive fuel regarding its ability to lower the melting and flowing temperature of spruce ... -
Effect of Gas Recycling on the Performance of a Moving Bed Temperature-Swing (MBTSA) Process for CO2 Capture in a Coal Fired Power Plant Context
(Peer reviewed; Journal article, 2017)A mathematical model of a continuous moving-bed temperature-swing adsorption (MBTSA) process for post-combustion CO2 capture in a coal-fired power plant context has been developed. Process simulations have been done using ... -
Effect of gear design on catch damage on cod (Gadus morhua) in the Barents Sea demersal trawl fishery
(Journal article; Peer reviewed, 2021-02)Damage incurred during the catch process is an indicator of the overall quality of fish and fish welfare. Because catch quality is difficult to improve once it has deteriorated, it is important to preserve quality during ... -
Effect of gear soak time on size selection in the snow crab pot fishery
(Journal article; Peer reviewed, 2019-06)In the commercial pot fishery for snow crab (Chionocetes opilio), size selection by the pots is important for reducing catch sorting and unintended mortality. In addition to mesh size and shape, selection in the pots relies ... -
Effect of gear soak time on size selection in the snow crab pot fishery
(Journal article; Peer reviewed, 2019)In the commercial pot fishery for snow crab (Chionocetes opilio), size selection by the pots is important for reducing catch sorting and unintended mortality. In addition to mesh size and shape, selection in the pots relies ... -
Effect of Geometrical Irregularities on Fatigue of Lead Sheathing for Submarine High Voltage Power Cable Applications
(Peer reviewed; Journal article, 2021)High voltage subsea power cables are typically composed of several layers, including: a conductive core, a dielectric layer, a ductile metallic watertight barrier and a series of radial and axial armours and polymer layers. ... -
Effect of gillnet twine thickness on capture pattern and efficiency in the Northeast-Arctic cod (Gadus morhua) fishery
(Journal article; Peer reviewed, 2023)Gillnets are among the most common fishing gears worldwide. They are often made of thin twine, which is prone to wear and tear, limiting the lifespan of the gillnet. This increases gillnet turnover, and consequently increased ... -
The Effect of Grain Refiner on Aluminium Filtration
(The Minerals, Metals & Materials Series;2367-1181, Peer reviewed; Journal article, 2021)Grain refinement of aluminium and its alloys is a common industrial practice. Fine equiaxed, grain structure leads to improved castability, strength, machinability, formability, and good surface finish. Filtration is one ... -
Effect of graphene coatings on the morphology of submillimeter thin copper wires after salt spray aging
(Peer reviewed; Journal article, 2023)Unprotected copper conductors are prone to oxidation and corrosion, especially when in contact with salt water or at high temperature. In this study, we compared commercially available coating with graphene oxide and ... -
Effect of grid section design on trawl size selectivity
(Journal article; Peer reviewed, 2023)Sorting grids are introduced in trawl fisheries to improve size selectivity and reduce the variability of results obtained with sorting devices constructed of netting e.g., codends. Grids are rigid or semi-rigid structures ... -
The effect of grid size on catch efficiency and by-catch in the demersal trawl fishery for Norway pout (Trisopterus esmarkii)
(Peer reviewed; Journal article, 2022)Norway pout (Trisopterus esmarkii) is caught with large trawls with small meshed codends, inevitably causing the fishery to have large by-catch issues. To reduce the amount of by-catch, a rigid sorting grid was made ... -
Effect of ground gear modification on bycatch of rays in mediterranean bottom trawl fishery
(Peer reviewed; Journal article, 2022)Bycatch of rays and skates in towed fishing gears represents one of the major threats to these relatively slow-growing marine species. The objective of this study was to modify ground gear in a bottom trawl fishery to ... -
Effect of harvesting month and proximity to fish farm sea cages on the lipid profile of cultivated Saccharina latissima
(Peer reviewed; Journal article, 2021)Macroalgae aquaculture is thriving, and kelps such as Saccharina latissima, are now farmed over different production sites across Europe. Macroalgae production in integrated multi-trophic aquaculture setups is gaining ... -
Effect of heat input on nanomechanical properties of wire-arc additive manufactured Al 4047 alloys
(Peer reviewed; Journal article, 2022)Heat input is one of the most important process parameters during additive manufacturing (AM). It is of great significance to understand the effect of heat input on the microstructure and nanomechanical properties, as well ... -
Effect of Heat Treatment on the Ductility of Inconel 718 Processed by Laser Powder Bed Fusion
(Lecture Notes in Electrical Engineering;1876-1100, Peer reviewed; Journal article, 2020)Inconel 718 is a precipitation-hardening alloy, with a typical heat treatment consisting of solution annealing before a two-stage ageing process. Depending on the heat treatment procedure, strength or ductility can be ... -
The effect of heavy deformation on the precipitation in an Al-1.3Cu-1.0Mg-0.4Si wt.% alloy
(Peer reviewed; Journal article, 2020)This work has investigated the effect of the combination of natural ageing and 80% pre-deformation after solution heat treatment on precipitation during subsequent artificial ageing in an Al-1.3Cu-1.0Mg-0.4Si wt.% alloy. ...