Blar i SINTEF Open på tittel
Viser treff 17-36 av 10035
-
2D-packing with an application to stowage in Roll-on Roll-off liner shipping
(Journal article; Peer reviewed, 2016-08-14)Roll-on/Roll-off (RoRo) ships represent the primary source for transporting vehicles and other types of rolling material over long distances. In this paper we focus on operational decisions related to stowage of cargoes ... -
2nd run of full 3-D detectors
(Lecture, 2009) -
3-D Snake Robot Motion: Nonsmooth Modeling, Simulations, and Experiements
(Journal article; Peer reviewed, 2008)A nonsmooth (hybrid) 3-D mathematical model of a snake robot (without wheels) is developed and experimentally validated in this paper. The model is based on the framework of nonsmooth dynamics and convex analysis that ... -
30 GW offshore wind in Norway : time series analysis based on numerical weather model dataset
(SINTEF Energi. Prosjektnotat;, Report, 2023-02-28)This memo investigates impacts of integrating 30 GW offshore wind in Norway -
30 tonns utslippsfri gravemaskin. Teknologistatus, kartlegging og erfaringer
(SINTEF Fag;52, Research report, 2018)Prosjektet "Zero Emission Digger" (ZED) har som hovedmål å realisere en prototyp for en utslippsfri 30 tonns beltegravemaskin. Hensikten med prosjektet er å utvikle en slik maskin fra et konseptdesign til et kommersielt ... -
3D Basin-Scale Groundwater Flow Modeling as a Tool for Geothermal Exploration: Application to the Geneva Basin, Switzerland-France
(Peer reviewed; Journal article, 2021)Switzerland promotes the energy transition by supporting the development of geothermal energy. We built a 3D basin-scale fluid flow model of the Geneva Basin, France-Switzerland, using the open-source Matlab Reservoir ... -
3D fluid modeling of positive streamer discharges in air with stochastic photoionization
(Peer reviewed; Journal article, 2020)Streamer discharges are thin plasma channels that precede lightning and sparks. They usually evolve in bundles as stochastic tree-like structures and are inherently difficult to model due to their multiscale nature. In ... -
3D graphene aerogel framework enwrapped LiFePO4 submicron-rods with improved lithium storage performance
(Journal article; Peer reviewed, 2019)The three-dimensional (3D) graphene aerogel (GA)-wrapped LiFePO4 submicron-rod composite (LFP@GA) has been prepared successfully through a solvothermal method followed with rapid freezedrying. Monodispersed LiFePO4 ... -
3D Integration of MEMS and IC: Design, technology and simulations
(Lecture, 2009)* 3D integration: Opportunities and trends* e-CUBES: Tire pressure monitoring system (TPMS)* Package design including thermo-mechanical modeling* Technology development* Sensor packaging concept* Gold stud bump bonding* ... -
3D Integration Technologies for Wireless Sensor Systems (e-CUBES)
(Lecture, 2008)The innovative approach presented here will realize so-called e-CUBES® (electronic cubes) [1], i.e. investigate and develop ultra small sensor cubes with dimensions of a few mm3 which are wirelessly communicating among ... -
3D Integration Technologies for Wireless Sensor Systems (e-CUBES)
(Lecture, 2008)The innovative approach presented here will realize so-called e-CUBES® (electronic cubes) [1], i.e. investigate and develop ultra small sensor cubes with dimensions of a few mm3 which are wirelessly communicating among ... -
3D Integration technology: Status and application development
(Journal article; Peer reviewed, 2010)As predicted by the ITRS roadmap, semiconductor industry development dominated by shrinking transistor gate dimensions alone will not be able to overcome the performance and cost problems of future IC fabrication. Today ... -
3D interconnect technologies for advanced MEMS/NEMS applications
(Lecture, 2009) -
A 3D kinetic Monte Carlo study of streamer discharges in CO2
(Peer reviewed; Journal article, 2024)We theoretically study the inception and propagation of positive and negative streamers in CO2. Our study is done in 3D, using a newly formulated kinetic Monte Carlo discharge model where the electrons are described as ... -
3D modelling of β'' in Al-Mg-Si: towards an atomistic level ab initio based examination of a full precipitate enclosed in a host lattice
(Peer reviewed; Journal article, 2014)We extend a first principles based hierarchical multi-scale model scheme for describing a fully coherent precipitate in a host lattice to 3D simulations. As our test system, the needle-shaped main hardening Al–Mg–Si alloy ... -
3D motion dynamics of axisymmetric bodies falling through water
(Journal article; Peer reviewed, 2018-12-01)A new simplified method for analysis of 3D motion dynamics of axisymmetric slender bodies falling from air through water is presented. Slender-body theory for potential flow of incompressible water is combined with 2D + t ... -
3D Printed PEI Containing Adsorbents Supported by Carbon Nanostructures for Post-combustion Carbon Capture From Biomass Fired Power Plants
(Peer reviewed; Journal article, 2021)Processes that utilize solid adsorbents to capture CO2 are promising alternatives to state-of-art Amine based technologies for capturing CO2 from large point sources. Although the energy needs of solid sorbent-based processes ... -
3D Radiation Detectors: Charge Collection Characterisation and Applicability of Technology for Microdosimetry
(Journal article; Peer reviewed, 2014)A study of charge collection in SINTEF 3D active edge silicon detectors was carried out at ANSTO using Ion Beam InducedCharge (IBIC) technique.An IBIC study has shown that several different geometries of 3D detectors have ... -
3D reconstruction of existing concrete bridges using optical methods
(Peer reviewed; Journal article, 2019)Routine bridge inspections usually consist of visual observations. These inspections are time-consuming and subjective. There is a need to identify new inspection techniques for infrastructure that reduce traffic disturbance, ...